Wood Sheeting Falls On Helper
A forklift operator's helper was crushed by a falling stack of wood sheeting. The incident occurred when the driver, using the forklift to reposition the load of wood, struck the pile of sheeting and knocked
A forklift operator's helper was crushed by a falling stack of wood sheeting. The incident occurred when the driver, using the forklift to reposition the load of wood, struck the pile of sheeting and knocked
A millworker died when the bulldozer he was driving rolled down an embankment. A lightning strike had caused a fire in the sawmill area. The fire department brought the fire under control and left the
A woman with a history of asthma was working on a lamination process known to release an isocyanate. She developed an acute attack of asthma which failed to respond to her aerosol medication. Co-workers took
A shortcut across a moving conveyor belt was a fatal decision for a worker. He was watching the conveyor when he noticed a piece of timber fall to the floor instead of into the waste
A former carpenter died of cancer at age 54. The disease began as skin cancer, caused by excessive exposure to the sun. During his career he was a framer, working on residential buildings. Traumatic injury
An operator of an excavator struck a water line while digging a trench, causing water to spray around. A worker in the trench took his shovel and started tossing water back at the excavator operator.
A building contractor died when he was trapped in the burning basement of a house under construction. Another worker was using an oxyacetylene cutting torch to cut I-beams over the basement of the house. Stray
A worker operating an automatic die-cast system died after being crushed between the back end of an industrial robot and a steel safety pole. The hydraulic robot had been installed in an existing production line
A worker was standing on a catwalk, using a vacuum with a long nozzle to clean a fast-moving conveyor belt. It appears the nozzle became caught between two large rollers and pulled the worker into
An employee who was hired as a sweeper and handyman was discovered sitting in a deposit of blue sludge, on the bottom of a deep steel vat. The man had, in the past, cleaned tanks
A welder in a metalwork plant pushed a 250 amp welder on a dolly over to a wall outlet. He plugged it in with his right hand while his left hand was on the welder.
Carbon monoxide killed a supervisor and an engineering draftsman when they entered a lime kiln to check the thickness of the metal walls. The kiln was not blocked off from another nearby kiln which had
An empty water tank weighing 14 tons (12.7 metric tons) was being lifted by a crane onto a water tower frame. The land around the new community water tower had been excavated the previous month
A spotter was crushed to death by a road roller during paving work. He had been guiding construction vehicles and general traffic on the road as asphalt pavement was being applied and finished. The roller

AThree experienced welders were killed recently in separate incidents while using torches to work on containers they believed were empty. In the first, a mechanic supervisor was using a torch to cut a 55-gallon metal
A mill supervisor was killed when he was hit by a piece of a door which blew off an anvil chipper. The incident occurred when a chipper saw knife fell into the conveyor system and
Would you trust your life to a hydraulic jack? You shouldn’t. Workers have been killed by vehicles and other heavy objects falling off jacks and improperly-placed jack stands. In one such fatality, a mechanic was
Many fatalities are caused by cave-ins of trenches that have not been shored up. This case report is about a fatality that occurred because shoring had been put in place but not braced. The victim
A young man was working as a welder at his weekend job. Situated on a platform approximately 17 feet above the concrete floor, he had been welding for about 15 minutes when he unexpectedly fell
The boom of a log loader dropped suddenly and killed a logging truck driver as he was helping load a pulp truck. He had climbed up an access ladder to the loader cab to hand
A worker driving an electric cart was run over and crushed by a forklift driver who could not see past his tall load. The incident occurred at a concrete pipe manufacturing plant where the man
Two workers were assigned to unload a barge tied up at a riverside dock. One was operating a front end loader to transfer lime into a portable conveyor to carry it up to the dock.

An experienced worker and his untrained helper lowered an aluminum ladder into an underground fuel storage tank. A small access hatch had been cut into the tank using a water cooled saw. One of the

A foreman placed a wooden ladder into a mixing vat that had recently been sprayed with a cleanser called methylene chloride. While on the ladder, he called over to a co-worker to start the fan in the vat.

Three workers, one licensed electrician and two apprentices, were rewiring a residential basement. They were using a 300 watt lightbulb, drawing power from a temporary connection to power wires on an outside pole. The electrician